Division 7 Ebook Page 487 Senergy Sentry Stucco Wall System, 07 24 16

8. Apply mixed [ALPHA] [ALPHA DRY] Base Coat to entire surface of EPS insulation and onto the Senerthik Base Coat a minimum of 64 mm (2 ) with a stainless steel trowel to embed the Reinforcing Mesh. 9. Immediately place FLEXGUARD 4 Reinforcing Mesh against wet Base Coat and embed the Reinforcing Mesh into the Base Coat by troweling from the center to the edges. 0. Lap Reinforcing Mesh 64 mm (2 1/2") minimum at edges. 11. Ensure Reinforcing Mesh is continuous at corners, void of wrinkles and fully embedded in Base Coat. 12. If required, apply a second layer of Base Coat to achieve total nominal Base Coat/Reinforcing Mesh thickness of 1.6 mm (1/16"). 13. Allow Base Coat with embedded Reinforcing Mesh to dry hard (normally 8 to 10 hours) prior to primer and finish application. NOTE TO SPECIFIER: If architectural features utilizing EPS insulation and reinforced base coat are incorporated onto the Sentry Stucco CI Wall System, then TINTED PRIMER is recommended over the entire Sentry Stucco CI Wall System prior to finish application.] [G. Senergy TINTED PRIMER: 1. Apply TINTED PRIMER to the Base Coat with a sprayer, 10 mm (3/8) nap roller, or good quality latex paint brush at a rate of approximately 3.6-6.1 m per liter (150-250 ft. per gallon). 2. TINTED PRIMER shall be dry to the touch before proceeding to the Senergy Finish Coat application.] H. SENERGY FINISH COAT [1.SENERFLEX FINISH: [CLASSIC] [FINE] [TEXTURE] [COARSE] [SAHARA] [BELGIAN LACE] [ENCAUSTO VERONA] [METALLIC]. - OR - SILCOAT FINISH: [CLASSIC] [FINE] [TEXTURE] [SAHARA] - OR - SENERLASTIC FINISH: [CLASSIC] [FINE] [TEXTURE] [SAHARA] [BELGIAN LACE] a. Apply FINISH directly to the stucco brown coat with a clean, stainless steel trowel. b. Apply and level FINISH during the same operation to minimum obtainable thickness consistent with uniform coverage. c. Maintain a wet edge on FINISH by applying and texturing continually over the wall surface. d. Work FINISH to corners, joints or other natural breaks and do not allow material to set up within an uninterrupted wall area. e. Float FINISH to achieve final texture.] [2.[AURORA TC-100] [BOREALIS] [ALUMINA] FINISH COAT a. Apply TINTED PRIMER to substrate in accordance with current Senergy TINTED PRIMER product bulletin. TINTED PRIMER shall be of corresponding color for selected [AURORA TC-100] [BOREALIS] [ALUMINA] FINISH color. Allow TINTED PRIMER to dry to the touch before proceeding to [AURORA TC-100] [BOREALIS] [ALUMINA] FINISH application. b. Apply a tight coat of FINISH with a clean, stainless steel trowel. c. Maintain a wet edge on FINISH by applying and leveling continually over the wall surface. d. Work FINISH to corners, joints or other natural breaks and do not allow material to set up within an uninterrupted wall area. Allow first coat to set until surface is completely dry prior to applying a second coat of FINISH. (Second coat not required for ALUMINA FINISH) e. For a smooth appearance, use a stainless steel trowel and apply the second coat of FINISH. Achieve final texture using circular motions. f. For a textured appearance, apply the second coat of FINISH using a spray gun and hopper. g. Double-back to achieve final texture. h. Total thickness of FINISH shall be approximately 1.6 mm (1/16"). [3.AURORA STONE FINISH COAT a. Apply TINTED PRIMER to substrate in accordance with current Senergy TINTED PRIMER product bulletin. TINTED PRIMER shall be of corresponding color for selected AURORA STONE FINISH color. Allow TINTED PRIMER to dry to the touch before proceeding to AURORA STONE FINISH application. b. Apply a coat of AURORA STONE FINISH using a spray gun and hopper, maintaining a wet edge. Work to corners, joints or other natural breaks and do not allow material to set up within an uninterrupted wall area. c. Allow first coat of AURORA STONE FINISH to set until surface is completely dry prior to applying a second coat of AURORA STONE FINISH. d. Apply a second coat of AURORA STONE FINISH using a spray gun and hopper; double back to achieve final texture. e. Thickness of AURORA STONE FINISH may vary between 1.6 mm (1/16") and 3.2 mm (1/8"), depending upon texture. Note: Spraying of AURORA STONE FINISH should be in the same manner and direction and by the same mechanic on a particular elevation or project whenever possible, to maintain a uniform appearance. Maintain consistent air pressure to minimize texture variations. Stator or rotor design pumps are not recommended. ] [I. BASF Wall System's ANTICOGLAZE: 1. Apply BASF Wall System's ANTICOGLAZE in accordance with recommendations contained in current product literature.]

Previous Page
Next Page