Division 7 Ebook Page 272 FOAMULARŪ 404/604/404RB/604RB XPS Insulation Product Data Sheet

Product Data Sheet FOAMULAR 404, 604, 404 RB and 604 RB Extruded Polystyrene (XPS) Rigid Foam Insulation 165F. In horizontal applications, FOAMULAR XPS Insulation may experience greater solar exposure than in vertical applications and it may be damaged by heat buildup. Simple precautions during construction can minimize the potential for heat related damage. Install only as much FOAMULAR XPS Insulation as can be covered in the same day. For horizontal applications always turn the print side down so the black print does not show to the sun which may, at times, act as a solar collector and raise the temperature of the foam surface under the print. Additional protection over FOAMULAR XPS Insulation such as added cover boards, reflective membrane surfaces, or pavers may be required in areas adjacent to reflective walls, parapets, rooftop equipment areas or other vertical surfaces that may reflect and intensify the sun's energy. Do not cover FOAMULAR XPS Insulation either stored (factory wrapped or unwrapped), or partially installed, with dark colored (non-white), or clear (non-opaque) coverings and leave it exposed to the sun. Examples of such coverings include but are not limited to filter fabrics, membranes, temporary tarps, clear polyethylene, etc. If improperly covered, and exposed to the right combination of sun, time and temperature, deformation damage may occur rapidly. When covering is necessary, use only white opaque material, or, cover with the final approved finish material as soon as possible. A white opaque cover reflects energy from the sun rather than absorbing it or passing it which reduces the potential for excessive heat exposure. Clear (non-opaque) coverings allow light energy from the sun to pass through rather than reflect it which may produce a partial greenhouse effect, trapping hot air and raising the temperature below the cover. See Owens Corning publication number 10015704, "Heat Build Up Due to Solar Exposure" for more information. Standards and Codes Compliance Meets ASTM C578 Type VI (404 and 404 RB) and Type VII (604 and 604 RB) UL Classified. A copy of UL Classification Certificate U-197 is available at www. owenscorning.com See UL ER8811-01 at UL.com Product and Packaging Data FOAMULAR 404, 604, 404 RB and 604 RB Extruded Polystyrene (XPS) Rigid Foam Insulation Material Packaging Extruded polystyrene closed-cell foam panel with continuous skin on face and back surface. Shipped in poly-wrapped units with individually wrapped or banded bundles. Thickness (in) Product Dimensions Thickness (in) x Width (in) x Length (in)" Pallet (Unit) Dimensions (typical) Width (ft) x Length (ft) x Height (ft) Square feet per Pallet Board feet per Pallet Bundles per Pallet Pieces per Bundle Pieces per Pallet Edges F-404/404 Ribbed F-404/404 Ribbed 2" 2 x 24 x 96 4 x 8 x 8 1,536 3,072 8 12 96 2" 2.5 x 24 x 96 4 x 8 x 8 1,152 2,880 8 9 72 3" 3 x 24 x 96 4 x 8 x 8 1,024 3,072 8 64 4" 4 x 24 x 96 4 x 8 x 8 768 3,072 8 6 48 Ribbed 2" 2 x 24 x 96 4 x 8 x 8 1,536 3,072 8 12 96 Rain channeled on all bottom edges and ribbed channels on the top surfaces Ribbed 3" 3 x 24 x 96 4 x 8 x 8 1,536 3,072 8 64 F-604/604 Ribbed 1" 1.5 x 24 x 96 4 x 8 x 8 2,048 3,072 8 16 128 Rain channeled on all bottom edges. 2" 2 x 24 x 96 4 x 8 x 8 1,536 3,072 8 12 96 3" 3 x 24 x 96 4 x 8 x 8 1,024 3,072 8 64 Ribbed 1" 1.5 x 24 x 96 4 x 8 x 8 2,048 3,072 8 16 128 Rain channeled on all bottom edges and ribbed channels on the top surfaces Ribbed 2" 2 x 24 x 96 4 x 8 x 8 1,536 3,072 8 12 96 Ribbed 3" 3 x 24 x 96 4 x 8 x 8 1,024 3,072 8 64 1. Product availability and lead times vary by region and by product. Consult your local Owens Corning sales representative for availability and lead times.

Previous Page
Next Page