Division 7 Ebook Page 258 FOAMULARŪ Tapered Roofing Products XPS Insulation Product Data Sheet

Product Data Sheet FOAMULAR Tapered Roofing Products Extruded Polystyrene (XPS) Rigid Foam Insulation heat related damage. Install only as much FOAMULAR XPS Insulation as can be covered in the same day. For horizontal applications always turn the print side down so the black print does not show to the sun which may, at times, act as a solar collector and raise the temperature of the foam surface under the print. Additional protection over FOAMULAR XPS Insulation such as added cover boards, reflective membrane surfaces, or pavers may be required in areas adjacent to reflective walls, parapets, rooftop equipment areas or other vertical surfaces that may reflect and intensify the sun's energy. Do not cover FOAMULAR XPS Insulation either stored (factory wrapped or unwrapped), or partially installed, with dark colored (non-white), or clear (non-opaque) coverings and leave it exposed to the sun. Examples of such coverings include but are not limited to filter fabrics, membranes, temporary tarps, clear polyethylene, etc. If improperly covered, and exposed to the right combination of sun, time and temperature, deformation damage may occur rapidly. When covering is necessary, use only white opaque material, or, cover with the final approved finish material as soon as possible. A white opaque cover reflects energy from the sun rather than absorbing it or passing it which reduces the potential for excessive heat exposure. Clear (non-opaque) coverings allow light energy from the sun to pass through rather than reflect it which may produce a partial greenhouse effect, trapping hot air and raising the temperature below the cover. See Owens Corning publication number 10015704, "Heat Build Up Due to Solar Exposure" for more information. Standards, Codes Compliance Meets ASTM C 578 Type IV (TP 25), Type VI (FOAMULAR 400 insulation), Type VII (FOAMULAR 600 insulation) UL (Underwriters Laboratories) Classified. A copy of UL Classification Certificate U-197 is available at www.owenscorning.com See ICC-ES Evaluation Report ESR-1061 at www.icc-es.org THERMAPINK 25: UL Roof Deck Constructions, tested in accordance with UL 1256, "Standard for Fire Test of Roof Deck Constructions" including Roof Deck Construction #457. Product and Packaging Data FOAMULAR Tapered Roofing Products Exturded Polystyrene (XPS) Rigid Foam Insulation Material Packaging Extruded polystyrene closed-cell foam, ASTM C578 Type IV, 25 psi minimum Shipped in poly-wrapped units with individually wrapped or banded bundles. Thickness (in) Product Dimensions Thickness (in) x Width (in) x Length (in) Pallet (Unit) Dimensions (typical) Width (ft) x Length (ft) x Height (ft) Square feet per Pallet Board feet per Pallet Bundles per Pallet Pieces per Bundle Pieces per Pallet THERMAPINK 25 and FOAMULAR 600 Tapered Insulation (FOAMULAR 400 Tapered Insulation only available in E, F and G panels.) 1 /8 slope A 0.5-0.75 x 24 x 96 4 x 8 x 8 4,608 2,880 24 12 288 1 /8 slope B 0.75-1 x 24 x 96 4 x 8 x 8 3,456 3,024 18 12 216 1 /8 slope C 1-1.25 x 24 x 96 4 x 8 x 8 2,688 3,024 14 12 168 1 /8 slope D 1.25-1.5 x 24 x 96 4 x 8 x 8 2,304 3,168 12 144 slope E 0.5-1 x 24 x 96 4 x 8 x 8 3,840 2,880 10 12 240 slope F 1-1.5 x 24 x 96 4 x 8 x 8 2,304 2,880 12 144 slope G 0.5-1.5 x 24 x 96 4 x 8 x 8 2,688 14 12 168 1. Available lengths and edge configurations vary by thickness. See www.foamular.com for current offerings. Other sizes may be available upon request. Consult your local Owens Corning representative for availability. Standard Product Availability FOAMULAR Tapered Roofing Products Panel THERMAPINK 25 Taper Insulation FOAMULAR 400 Taper Insulation FOAMULAR 600 Taper Insulation 1 /8 slope A X 1 /8 slope B X 1 /8 slope C X 1 /8 slope D X slope E X slope F X slope G X

Previous Page
Next Page