Division 7 Ebook Page 15 Insulation Systems for Commercial Buildings

PAGE 10 1-800-GET-PINK www.owenscorning.com FIBERGLAS 700 SERIES INSULATION FIBERGLASS INSULATION-PRODUCT DATA DESCRIPTION & USES Unfaced FSK-faced (Foil-Scrim Kraft) ASJ (All Service) Flexible, semi-rigid and rigid rectangular boards formed from inorganic glass fibers with a thermosetting resin binder. 701, 702, 711-Unfaced, lightweight, resilient insulation in a sheet form, used on vessels with irregular surfaces where an exterior finish will be supported mechanically. 703, 704-Semi-rigid boards for use on equipment, vessels and air conditioning ductwork. Available unfaced, with factory- applied FSK, ASJ or vapor retarding facings. 705-High-strength, rigid board for use on equipment where high abuse resistance and good appearance are required. Available unfaced or with factory-applied FSK, ASJ or vapor retarding facings. 707-For acoustical wall panels and specialized ceiling applications. FEATURES & BENEFITS Helps save energy and reduce heat transfer. Available in various densities to meet specific performance, appearance and economic requirements. Resists damage and maintains structural integrity. Excellent acoustic properties. AVAILABILITY Fiberglas 700 Series Insulations are available in standard 24" x 48" (610 mm x 1219 mm) boards with thicknesses from 1" (25 mm) to 4" (102 mm) in " (13 mm) increments. Contact your Owens Corning Sales Representative for additional sizes or if specific labeling is required for air handling. SPECIFICATION COMPLIANCE ASTM C553, Mineral Fiber Blanket Thermal Insulation, Types I, II, III-Type 701, 711 ASTM C612, Mineral Fiber Block & Board Thermal Insulation, Types IA, IB-Types 702, 703, 704, 705, 707 ASTM C795, Thermal Insulation For Use Over Austenitic Stainless Steel 1 ASTM C1136, Flexible Low Permeance Vapor Retarders for Thermal Insulation, Type I: ASJ; Type II: FSK Nuclear Regulatory Commission Guide 1.36, Non-Metallic Thermal Insulation 1 New York City MEA No. 227-83-Types 703 & 705, plain and FSK-faced CAN/CGSB-51.10-Type I, Class I-Types 703, 704 2 NFPA 90A and 90B California Insulation Quality Standards CA-T052 1. Preproduction qualification testing complete and on file. Chemical analysis of each production lot required for total conformance. 2. Standard obsolete, replaced by ASTM C612. PHYSICAL PROPERTY DATA PROPERTY TEST METHOD VALUE Equipment Operating Temperature Limitation ASTM C411 Up to 450F (232C) 1 Insulation Jacket Temperature Limitation ASTM C1136 -20F to 150F (-29C to 66C) Jacket Permeance ASTM E96, Proc. A 0.02 perm Jacket Puncture Resistance TAPPI T803 FRK: 25 units; ASJ: 50 units Compressive Strength (Minimum) ASTM C165 Type 703 Type 704 Type 705 at 10% Deformation 25 lb/ft 2 (1,197 Pa) 60 lb/ft 2 (2,873 Pa) 200 lb/ft 2 (9,576 Pa) at 25% Deformation 90 lb/ft 2 (4,309 Pa) 225 lb/ft 2 (10.8 kPa) Water Vapor Sorption ASTM C1104 Max. 5% by Weight Nominal Density ASTM C167 Type 701: 1.5 pcf (24 kg/m 3 ) 711: 1.65 pcf (26 kg/m 3 ) 702: 2.3 pcf (37 kg/m 3 ) ASTM C303 703: 3.0 pcf (48 kg/m 3 ) 704: 4.2 pcf (67 kg/m 3 ) 705: 6.0 pcf (96 kg/m 3 ) 707: 7.0 pcf (112 kg/m 3 ) Composite Surface Burning Characteristics UL 723 2 , ASTM E84 2 or CAN/ULC-S102 2 Flame Spread 25 2 Smoke Developed 50 1. Maximum thickness at 450F (232C): Type 701, 702: 6" (152 mm); Type 703, 704, 705: 4" (102 mm). 2. The surface burning characteristics of these products have been determined in accordance with ASTM E84, UL 723 or CAN/ULC-S102. This standard should be used to measure and describe the properties of materials, products or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. Values are reported to the nearest 5 rating. Up To 48" Up To 96" Recommended impaling pin pattern. Pins should be located 3" to 8" from the edge(s) of the board. Up To 24" Up To 48" Up To 48" Up To 96" WALLS: 703 AND 705 SERIES CEILINGS: 703 AND 705 SERIES

Previous Page
Next Page