Division 22 23 Ebook Page 65 Pipe and Mechanical Insulation Brochure

38 Physical property data Property Value Test Method Operating Temperature up to 250F (121C) ASTM C411 Insulation Jacket Temperature Limit up to 150F (66C) ASTM C1136 Jacket Puncture Resistance 25 units (0.7 joules) ASTM C1136 Water Vapor Permeance 0.02 perms ASTM E96 Water Vapor Sorption <3% by weight at 120F (49C), 95% R.H. ASTM C1104 Fungi Resistance Meets requirements ASTM C1338 Thermal Conductivity Out-of-Package k-Value k Btuin/hrft2F ( at 24C Mean, W/mC) Installed (Compressed) k-Value k Btuin/hrft2F ( at 24C Mean, W/mC) Type 75 0.30 (0.043) Type 75 0.27 (0.039) Type 100 0.27 (0.039) Type 100 0.25 (0.036) Type 150 0.25 (0.036) Type 150 0.23 (0.033) ASTM C518 Surface Burning Characteristics 1 Flame Spread: 25 Smoke Developed: 50 ASTM E84 1. The surface burning characteristics of these products have been determined in accordance with ASTM E 84. This standard should be used to measure and describe the properties of materials, products or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. Values are reported to the nearest 5 rating. SoftR Duct Wrap Availability & installed R-values Standard roll width: 48" (1.2m) Installed R (RSI) values: When installed in accordance with recommended installation procedures, SoftR Duct Wrap will provide installed R (RSI) values as follows: Nominal Thickness Out-of-Package R (RSI) Value 1 Installed Thickness 2 Installed R (RSI) Value 1,2 Roll Length in. mm in. mm TYPE 75 - 0.75 pcf (12 kg/m 3 ) 1.5 (38) 5.1 (0.90) 1-1/8 (29) 4.2 (0.74) 100' 2.0 (50) 6.8 (1.17) 1-1/2 (38) 5.6 (0.98) 75 2.2 (56) 7.4 (1.30) 1-5/8 (42) 6.0 (1.06) 75 3.0 (76) 10.0 (1.76) 2-1/4 (57) 8.3 (1.46) 50' TYPE 100 - 1.00 pcf (16 kg/m 3 ) 1.5 (38) 5.6 (0.99) 1-1/8 (29) 4.5 (0.79) 100' 2.0 (51) 7.4 (1.30) 1-1/2 (38) 6.0 (1.06) 75 TYPE 150 - 1.50 pcf (24 kg/m 3 ) 1.5 (38) 6.0 (1.06) 1-1/8 (29) 4.8 (0.85) 75 2.0 (51) 8.0 (1.41) 1-1/2 (38) 6.4 (1.13) 50' 1. hr ft2 F/ Btu (m2 C/ W) at 75F (24C) mean temperature. 2. Assumes 25% compression of insulation.

Previous Page
Next Page