Division 22 23 Ebook Page 151 QuietR Duct Board Product Data Sheet

Limitations Fiberglass ducts should not be used in the following applications: Kitchen or fume exhaust ducts, or to convey solids or corrosive gases; In concrete or buried below grade; Outdoors; As casings and/or housings of built-up equipment; Immediately adjacent to high temperature electric heating coils without radiation protection; For vertical risers in air duct systems serving more than two stories in height; With coal or wood fueled equipment, or with equipment of any type which does not include automatic maximum temperature controls; In variable air volume systems on the high pressure side unless reinforced to withstand the full fan pressure; As penetrations in construction where fire dampers are required, unless the fire damper is installed in a sheet metal sleeve extending through the fire wall; or When the duct system is located in non-conditioned space and is used for cooling only (when heating is from another source), unless all registers which would allow moist air into the duct system are vapor sealed during the heating season to prevent condensation from forming inside the duct. Standards, Codes Compliance Meets UL 181 Class 1 Air Ducts Meets NFPA 90A/90B Meets ICC International Mechanical Code, Corps of Engineers Guide Spec. Supported by NAIMA and SMACNA industry standards Meets requirements of UL 181 and ASTM C1338 (mold growth), ASTM G21 (fungi test) and ASTM G22 (bacteria test) Fabrication and Installation Fabrication and installation of fiber glass Duct Systems shall be in accordance with the UL listing and shall conform to Owens Corning's published methods and/or latest editions of NAIMA (North American Insulation Manufacturers Association) Fibrous Glass Duct Construction Standards (AH116 or AH119) or SMACNA (Sheet Metal and Air Conditioning Contractors National Association) Fibrous Glass Duct Construction Standards. UL181A Listed Closure UL 181A Listed Closure must be employed to meet the requirements of UL 181/ULC S110. USE OF A NON-LISTED CLOSURE SYSTEM VOIDS THE UL CLASS 1 AIR DUCT RATING. The following are the listed closure methods: Pressure-Sensitive Tape (UL 181A-P) Mastic and Glass Fabric (UL 181A-M) Heat-Activated Tape (UL 181A-H) Cleanability The durable mat air stream surface makes it easy to clean the duct system using methods and equipment described in North American Insulation Manufacturers Association (NAIMA) Publication AH122, Cleaning Fibrous Glass Insulated Duct Systems. Environmental and Sustainability Owens Corning is a worldwide leader in building material systems, insulation and composite solutions, delivering a broad range of high-quality products and services. Owens Corning is committed to driving sustainability by delivering solutions, transforming markets and enhancing lives. More information can be found at www.owenscorning.com. Notes For additional information, refer to the Safe Use Instruction Sheet (SUIS) found in the SDS Database via http://sds.owenscorning.com Disclaimer of Liability Technical information contained herein is furnished without charge or obligation and is given and accepted at recipient's sole risk. Because conditions of use may vary and are beyond our control, Owens Corning makes no representation about, and is not responsible or liable for the accuracy or reliability of data associated with particular uses of any product described herein. SCS Global Services provides independent verification of recycled content in building materials and verifies recycled content claims made by manufacturers. For more information, visit www.SCSglobalservices.com. LEED is a registered trademark of the U.S. Green Building Council. Certifications and Sustainable Features Certified by SCS Global Services to contain a minimum of 53% recycled glass content, 31% pre-consumer and 22% post-consumer GREEN GUARD Certified products are certified to GREENGUARD standards for low chemical emissions into indoor air during product usage. For more information, visit ul.com/gg* Environmental Product Declaration (EPD) has been certified by UL Environment Material Health Certificate from Cradle to Cradle Products Innovation Institute Pub. No. 57577-N. Printed in U.S.A. October 2016. THE PINK PANTHER & 1964-2016 Metro-Goldwyn-Mayer Studios Inc. All Rights Reserved. The color PINK is a registered trademark of Owens Corning. 2016 Owens Corning. All Rights Reserved. OWENS CORNING INSULATING SYSTEMS, LLC ONE OWENS CORNING PARKWAY TOLEDO, OHIO, USA 43659 1-800-GET-PINK www.owenscorning.com *GREENGUARD certification is for boards 1" or less in thickness

Previous Page
Next Page