Division 22 23 Ebook Page 125 Fiberglasí Pipe Insulation Product Data Sheet

Product Data Sheet FIBERGLAS Pipe Insulation 8. Apply systems identification labels by pressure-sensitive labels, or by stencil with spray paint. No Wrap 1. Open the hinged sections and place over the pipe, carefully aligned and secured by wires or bands. 2. Jacket and vapor seal as required by the application. Personnel Protection Table Thickness Required for Surface Temperatures 140 F, inches (mm) 5,6 Nominal Pipe Size System Operating Temperatures F (C) in. (mm) 200F (93C) 300F (149C) 400F (204C) 500F (260C) 600F (316C) 800F (427C) 0.5 (15) 0.5 (15) 0.5 (15) 0.5 (15) 1.0 (25) 1.0 (25) 1.5 (38) 0.75 (20) 0.5 (15) 0.5 (15) 0.5 (15) 1.0 (25) 1.5 (38) 2.0 (51) 1 (25) 0.5 (15) 0.5 (15) 0.5 (15) 1.0 (25) 1.5 (38) 2.0 (51) 1.25 (32) 0.5 (15) 0.5 (15) 1.0 (25) 1.0 (25) 1.5 (38) 2.0 (51) 1.5 (40) 0.5 (15) 0.5 (15) 1.0 (25) 1.0 (25) 1.5 (38) 2.0 (51) 2 (50) 0.5 (15) 0.5 (15) 1.0 (25) 1.0 (25) 1.5 (38) 2.0 (51) 2.5 (65) 0.5 (15) 0.5 (15) 1.0 (25) 1.0 (25) 1.5 (38) 2.0 (51) 3 (80) 0.5 (15) 0.5 (15) 1.0 (25) 1.0 (25) 1.5 (38) 2.5 (64) 4 (100) 0.5 (15) 0.5 (15) 1.0 (25) 1.0 (25) 1.5 (38) 2.5 (64) 5 (125) 0.5 (15) 0.5 (15) 1.0 (25) 1.0 (25) 1.5 (38) 2.5 (64) 6 (150) 0.5 (15) 0.5 (15) 1.0 (25) 1.5 (38) 1.5 (38) 2.5 (64) 7 (175) 0.5 (15) 0.5 (15) 1.0 (25) 1.5 (38) 1.5 (38) 2.5 (64) 8 (200) 0.5 (15) 0.5 (15) 1.0 (25) 1.5 (38) 1.5 (38) 2.5 (64) 9 (225) 0.5 (15) 0.5 (15) 1.0 (25) 1.5 (38) 1.5 (38) 2.5 (64) 10 (250) 0.5 (15) 0.5 (15) 1.0 (25) 1.5 (38) 1.5 (38) 2.5 (64) 12 (300) 0.5 (15) 0.5 (15) 1.0 (25) 1.5 (38) 1.5 (38) 3.0 (76) 14 (350) 0.5 (15) 0.5 (15) 1.0 (25) 1.5 (38) 2.0 (51) 3.0 (76) 16 (400) 0.5 (15) 0.5 (15) 1.0 (25) 1.5 (38) 2.0 (51) 3.0 (76) 18 (450) 0.5 (15) 0.5 (15) 1.0 (25) 1.5 (38) 2.0 (51) 3.0 (76) 20 (500) 0.5 (15) 0.5 (15) 1.0 (25) 1.5 (38) 2.0 (51) 3.0 (76) 24 (600) 0.5 (15) 0.5 (15) 1.0 (25) 1.5 (38) 2.0 (51) 3.0 (76) 30 (750) 0.5 (15) 0.5 (15) 1.0 (25) 1.5 (38) 2.0 (51) 3.0 (76) 5. Calculations estimated using NAIMA 3E Plus Version 4.0 Software. Fixed Design Conditions: Steel horizontal piping, 80F (27C) average ambient temperature, 0 mph wind speed and outer surface jacket emittance of 0.9. For alternate design conditions, contact your Owens Corning representative. 6. Thermal conductivity values used in these calculations are subject to normal manufacturing tolerances. Thickness to Prevent Surface Condensation Owens Corning ASJ Max Jacket for up to 16" NPS (400mm DN), in. (mm) 7,8 Ambient Temperature Relative Humidity System Operating Temperatures F (C) 35F (2C) 45F (7C) 55F (13C) 110 (43) 70% 1 (25) 80% 1 (38) 1 (38) 1 (38) 90% 3 (89) 3 (89) 3 (76) 100 (38) 70% 1 (25) 80% 1 (38) 1 (38) 1 (25) 90% 3 (89) 3 (76) 2 (64) 90 (32) 70% 1 (25) 80% 1 (38) 1 (25) 90% 3 (89) 3 (76) 2 (64) 80 (27) 80% 1 (38) 1 (25) 90% 3 (76) 2 (64) 2 (51) 70 (21) 80% 1 (25) 90% 2 (64) 2 (51) 1 (25) 7. Calculations estimated using NAIMA 3E Plus version 4.0 software. Fixed design conditions: Steel Horizontal Piping, 16" NPS, 0 mph wind speed, Outer Surface Jacket Emittance of 0.9. 8. Thermal conductivity values used in these calculations are subject to normal manufacturing tolerances.

Previous Page
Next Page