Division 22 23 Ebook Page 107 Fiberglas’ Insu-Quick® Insulation Product Data Sheet

Description Fiberglas Insul-Quick Insulation is a lightweight insulation composed of glass fibers bonded together in a semi-rigid, boardlike form with a special high temperature binder. Key Features Thermal efficiency helps conserve energy and lower costly heat loss. Easy to handle and install, even when large size boards are used and won't crumble or break during installation. Resists tearing and pulling apart, which contributes to excellent long-term installed thermal performance. Boards in sizes to 4' by 8' (1.2m x 2.4m) help reduce the number of joints, speeding installation and eliminating potential sources of heat leakage. Product Applications Fiberglas Insul-Quick Insulation is designed for use on power and process boilers, breechings, ducts, precipitators, chimney liners and other heated equipment operating at temperatures up to 850F (454C). It is used in applications where an outside facing of metal or metal mesh with a finishing cement is required. It can also be used as insulation in a metal panel system. Fiberglas Insul-Quick Insulation is used in panel systems. It is secured to the panel using pins and clips with metal mesh. Panels can be erected flush to heated surfaces or away from them and secured to buckstays or breeching and ductwork angle iron stiffeners. Fiberglas Insul-Quick Insulation can be installed directly to hot, flat or curved surfaces. It can be attached using welded pins or studs and finished with sheet metal; or using metal mesh and insulating cement, then canvassed and painted. Pins with speed washers or studs and nuts should be installed on 12" (300mm) x 18" (450mm) (approx.) centers and the insulation impaled over them. The sheet metal or metal mesh is secured to the same fasteners. Joints of the sheet metal are offset from joints of the insulation. For temperatures over 400F (204C), good practice suggests double layer application, regardless of insulation type. Single layer installation requires good workmanship to minimize heat loss and hot spots at insulation joints. Fiberglas Insul-Quick Insulation may be installed in either single or multiple layers up to a maximum of 6" (152mm) at all temperatures up to 850F (454C), or to a maximum of 8" (203mm) at temperatures not over 650F (343C). Standards, Codes Compliance ASTM C612, Mineral Fiber Block & Board Thermal Insulation, Types IA, IB, II Availability Sizes, in. (m) Thickness, in. (mm) 24" x 48" (0.6m x 1.2m) 1" (25mm) through 4" (102mm) in " (13mm) increments 36" x 48" (0.9m x 1.2m) Select additional sizes available Physical Property Data Property Test Method Value Hot Surface Performance ASTM C411 Up to 850F (454C) Maximum thickness 6" (152 mm) Up to 650F (343C) Maximum thickness 8" (203 mm) Compressive Strength at 10% Deformation at 20% Deformation ASTM C165 90 lb/ft 2 (4309 Pa) 130 lb/ft 2 (6225 Pa) Nominal Density ASTM C303 3.0 pcf (48 kg/m 3 ) Water Vapor Sorption ASTM C1104 < 2.0% by weight, at 120F (49C), 95% R.H. Shot Content ASTM C1335 Negligible Composite Surface Burning Characteristics 1 Flame Spread Smoke Developed UL 723, ASTM E84 or CAN/ULC-S102 25 50 1. The surface burning characteristics of these products have been determined in accordance with UL 723, ASTM E84 or CAN/ULC-S102.This standard should be used to measure and describe the properties of materials, products or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. Values are reported to the nearest 5 rating. Fiberglas Insul-Quick Insulation Product Data Sheet

Previous Page
Next Page